11/29/2023 0 Comments Fiat scudo 2.0 jtd reviewsIt is expected to consume 57 percent more fuel than factory data in real conditions and during test drives. Top speed is limited by 165 km/h (103 mph).Īnd combined fuel consumption is 7.0 lt/100km according to official factory data.Įstimated Scudo Kombi 2.0 JTD 16V (5-Seater) real World MPG/consumption is 11,2 lt/100km. Vehicle can accelerate from zero to 100 km/h (60 mph) in 14.2 seconds. If i tap the instrument cluster, the needle jumps up to full and back to half. You might not have been planning on your businesss next mid-sized van being a Fiat. The power is transmitted by a 5 speed Manual gearbox with Front wheel drive wheel drive. Hi all, I have just got a scudo 2001 2.0 jtd, it is remarkably agile and spacious, my only real gripe is that the fuel gauge sticks just under half way, occasionally shooting up to full, then falling back. With 1997 cc engine size it produces 109 horsepower and 270 Nm torque. Scudo Kombi 2.0 JTD 16V (5-Seater) has a 2,0 l Diesel engine. Scudo Scudo I Kombi is a 4 doors Coupe - Cabriolet in D class / Large car.Īutomobile weight is 1656 kg with 849 liters trunk loading capacity. Mk2 Punto).Fiat Scudo Kombi 2.0 JTD 16V (5-Seater)ReviewĢ006 Fiat Scudo 2.0 JTD’s production started in 2004 and continued in 2004, 20. This why for some cars you may need the older interface or even both types (e.g. However the "dumb" KL interfaces typified by "Vag-Com" (originally for VW Audi) can be driven directly by the software (called "bit-banging" by code writers) to accomodate these systems. Some older cars and systems used specialised variation of the KL interface to provide extra functionality. We are lucky to have software for €50 that does what the main dealer "informer" and expensive commercial sytems like those from Snap-On and Autodata. There should be a breather screwed into the box near the top, that can also be used for filling oil. If it does not have a level plug the correct procedure is to drain all the oil and refill with the correct volume of the correct oil. Make/Model specific software such as Multiecuscan give much more information and also send data to do things like turn on lights, reset learnt data and Proxi-alignment. Depending on the type of box it may or may not have a level plug. The software on the PC decodes the data into something useful.Generic software just identifies the common codes and basic fault / service reset. This is fine for newer (post 2005 or so) cars. The ELM 327 chip and it's clones only works with standard implementations of the common interfaces (K line and CAN). If you are reasonably competent with a soldering iron it's fairly easy to remove the resistor. If you have multimeter you can check for this problem by measuring the resistance between pins 6 and 14 with the interface unplugged from the car and computer. There is another potential issue with some interfaces is a 120 ohm resistor connected across the CAN bus (pins 6 and 14 of the OBD connector) this can cause bad connection to the bus on some cars or modules. Just follow the Multiecuscan installation instructions. This needs a driver, but they are so common that windows should find it without the disk. Most interfaces are USB so also have a serial to USB converter chip such as those made by FTDI. The ELM interface chip (the interfaces from China almost certainly use bootleg chips) converts from the OBD buses (K/L and CAN) protocols to "readable" (ASCII) serial data. No you don't need any software from the disk.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |